Get a quote
TL-09

Gutter Calculator: Length, Downpipes and Brackets

Enter the length of eaves, the number of straight runs and the height to the gutter. You get the gutter length, downpipes, brackets and fittings to plan for.

A worker fitting a white seamless aluminium gutter to the fascia of a South African house
A worker fitting a white seamless aluminium gutter to the fascia of a South African house

Gutter & Downpipe Calculator

Change any measurement and the answer updates as you type.

Measuring sheetTL-09
Each wall section with its own ends
8–10 m in heavy-storm areas; up to 12 m elsewhere

Downpipes3 downpipes

Gutter length to order
31.5 m (incl. 5% for offcuts if sectional)
Downpipe length
9.0 m (incl. 300 mm per offset bend)
Gutter brackets (every 800 mm)
40
Downpipe brackets (every 1.8 m)
6
Stop ends
4
Corner pieces
2
Outlets (drop pieces)
3
Drop over the longest run to an outlet
30 mm over 10.0 m
  • Place outlets near corners or in the middle of long runs: water then flows both ways and each half needs less fall.
  • Where a downpipe empties near the house, add a splash block or connect it to a stormwater drain to keep water away from the foundations.
Estimates only: confirm quantities with your supplier or contractorTL-09

Gutters only work if the water has somewhere to go. This gutter calculator turns your eaves length, runs, corners and wall height into a parts list: gutter length, downpipes, brackets, stop ends, corners and outlets. It also shows the drop needed along the longest run. The figures are estimates, so check the fittings and profile your supplier sells before you order.

How the gutter calculation works

The number of downpipes is the eaves length divided by the maximum gutter length per downpipe, rounded up. It is never fewer than the number of separate runs, because every run needs its own outlet. The default is 10 m per downpipe.

  • Gutter length: eaves length plus 5% for offcuts.
  • Downpipe length: height to the gutter plus 300 mm for offset bends, per downpipe.
  • Gutter brackets: one every 800 mm, plus one per run.
  • Downpipe brackets: one every 1.8 m, at least two per pipe.
  • Stop ends: two per run, with an outlet for each downpipe.

How to measure and set the fall

Measure the eaves along the fascia, wall section by wall section. Count each straight run separately, and count the corners. Measure the height from the ground to the gutter at each downpipe position.

Gutters need a slight fall towards the outlet. The calculator uses 3 mm per metre and shows the total drop over the longest run. Placing outlets near corners or in the middle of a long run lets water flow both ways, so each half needs less fall.

Practical tips for South Africa

In heavy-storm areas, such as Highveld thunderstorm country and parts of KZN, keep to 8 to 10 m per downpipe. Up to 12 m can work elsewhere. Clear leaves, hail debris and dust before the rainy season, from October on the Highveld and before May in the Western Cape.

Where a downpipe empties near the house, add a splash block or connect it to a stormwater drain. This keeps water away from the foundations. Check that the water has not been running down the wall behind the gutter.

When to call a pro

Call a gutter specialist for high two-storey eaves, sagging or rusted gutters, or persistent overflow. Standing on ladders near the edge of a roof is risky, so do not take chances. Ask about any roof repairs at the same time.

HandymanService.co.za does not fit gutters or sell them. Use the form on this page to get a free quote from independent gutter installers and suppliers.

Frequently asked questions

How many downpipes do I need?
Divide the total gutter length by the maximum run per downpipe, then round up. The default is 10 m. Every separate run needs at least one outlet. The calculator applies both rules and shows the result as downpipes.
How much fall should a gutter have?
The calculator uses 3 mm per metre, which you can change. It then shows the drop over the longest run to an outlet. Placing the outlet near the middle of a long run halves the distance and so reduces the fall needed.
How far apart should gutter brackets be?
The calculator allows a bracket every 800 mm, plus one extra per run. Downpipes get a bracket every 1.8 m, with a minimum of two. Your gutter maker may recommend a different spacing, so follow their instructions.
Why do gutters overflow in heavy rain?
The usual causes are blocked outlets, too few downpipes and gutters that do not slope towards the outlet. In storm-prone areas, use shorter runs per downpipe, such as 8 to 10 m, and clean the gutters before the rainy season.

More calculators and guides

Get a free quote

Tell us the job and where it is. A handyman, contractor or supplier who works in your area quotes you directly.

Job cardNo. 63811
  1. 1Tick the jobs and describe the work.
  2. 2We pass it to someone who works near you.
  3. 3They quote you. Free, no obligation.
Tick what needs doing (optional)

Free and no obligation. By sending you agree that we may share your request with a suitable handyman, contractor or supplier. See our privacy policy.

Get a free quote