Get a quote
TL-08

Roof Calculator: Area, Pitch and How Many Tiles or Sheets

Enter the building's length, width and roof pitch to get the true roof area. The calculator then works out concrete tiles or sheet counts for a gable or lean-to roof.

A roofer replacing broken concrete roof tiles on a pitched roof of a South African suburban house
A roofer replacing broken concrete roof tiles on a pitched roof of a South African suburban house

Roof Area, Pitch & Sheeting Calculator

Change any measurement and the answer updates as you type.

Measuring sheetTL-08
Concrete tiles 17.5–45°; IBR from about 5°
Only for tiles; check the profile, usually 9.5–11

Roof tiles (incl. 5% extra)1,325 tiles

Plan area (as seen from above)
108.0 m²
Roof area (true surface)
120.2 m²
Pitch factor
1.113
Slope length (wall plate to ridge)
5.01 m
Height of the ridge above the eaves
2.19 m
Ridge length
12.0 m: about 32 ridge tiles
  • Hipped roofs have the same area as a gable roof of the same pitch over the same plan; they just need more cutting and hip tiles.
  • Measure on the ground, not on the roof: the building's outside walls plus the overhang on each side.
Estimates only: confirm quantities with your supplier or contractorTL-08

A roof is bigger than the building underneath it, because the slope adds surface. This roof calculator turns the plan size and pitch into the true roof area, the slope length and the height of the ridge. It then counts tiles with a 5% allowance, or sheets by their cover width. These are estimates, so check the profile and cover width with your supplier.

How the roof calculation works

The plan area is length times width. The true roof area is the plan area multiplied by a pitch factor, which is 1 divided by the cosine of the pitch angle. At 26 degrees the factor is about 1.11. A steeper roof has a larger factor.

  • Slope length: half the width for a gable, or the full width for a lean-to, times the pitch factor.
  • Tiles: true area times tiles per square metre (10.5 by default), plus 5%.
  • Ridge tiles: about 2.6 per metre of ridge on a gable roof.
  • Sheets: roof length divided by the cover width (686 mm for IBR, 762 mm for corrugated), rounded up, per slope.

How to measure properly

Measure on the ground, not on the roof. Take the outside walls plus the overhang on each side. Hipped roofs have the same area as a gable roof of the same pitch over the same plan, but they need more cutting and hip tiles.

Concrete tiles need a minimum pitch, and below 17.5 degrees the calculator warns you to check the maker's minimum. IBR sheets can go lower, from about 5 degrees. Always confirm the figures on the product's data sheet.

Practical tips for South Africa

On the Highveld and in other summer-rainfall areas, hail and thunderstorms from October to March test every fixing and flashing. Do roof work in the dry winter months. In the Western Cape, winter rain from May to August makes summer the better season for roofing.

Coastal salt attacks unprotected steel, so choose coated sheets and suitable fixings near the sea. Order a little extra of one batch, since tile and sheet colours can vary.

When to call a pro

A new roof structure usually needs an engineer's or truss supplier's certificate for the municipality, and extensions need approved plans. Working at height is dangerous, so use a roofing contractor for anything beyond a small repair.

HandymanService.co.za does not do roofing or sell materials. Use the form on this page to get a free quote from independent roofing contractors and suppliers.

Frequently asked questions

How do I work out roof area from the pitch?
Multiply the building's plan area by the pitch factor, which is 1 divided by the cosine of the angle. A 26 degree roof has a factor of about 1.11. The calculator does this for you and also gives the slope length.
How many roof tiles do I need per square metre?
The default is 10.5 tiles per square metre, with 5% extra added. Profiles differ, and many fall between 9.5 and 11. Check the figure on your tile's data sheet or ask the supplier, then enter it in the tiles per m² field.
What pitch do I need for concrete tiles or IBR?
Concrete tiles are usually fitted from 17.5 degrees up to about 45. IBR sheets can work from around 5 degrees. Because ratings vary, the calculator flags low pitches, but always confirm the minimum with the manufacturer.
Is the roof area the same as the floor area?
No. The roof is larger because of the slope and the overhangs. A flat measurement of the building undercounts the covering you need. Use the building width including the overhangs, and let the pitch factor add the slope.

More calculators and guides

Get a free quote

Tell us the job and where it is. A handyman, contractor or supplier who works in your area quotes you directly.

Job cardNo. 35552
  1. 1Tick the jobs and describe the work.
  2. 2We pass it to someone who works near you.
  3. 3They quote you. Free, no obligation.
Tick what needs doing (optional)

Free and no obligation. By sending you agree that we may share your request with a suitable handyman, contractor or supplier. See our privacy policy.

Get a free quote